Upcycled Bunny Treat Jar (2024)

• Mayonnaise jar (2qt)
• Petroleum jelly (Vaseline)
• Masking tape
• Utility knife
• Fry pan/stove
• Glass measuring cup - small 2c
• Thin fiber board or cardboard
• Scissors
• Acrylic paint/brush
• White burlap fabric
• Fabri-Tac glue
• Macrame cord - white 5mm
• Bunny ear template
• Clamps
• Decorative ribbon -1"wide

I had a time removing all of the label and glue left on the jar while trying to clean it. I tried acetone and alcohol, but nothing seemed to work. Then I remembered someone mentioning using petroleum jelly to remove stubborn label glue.

So I spread on lots of Vaseline where the label and glue were and let that sit overnight.

The next day, I wiped the Vaseline off with a paper towel and SURPRISE - the glue was all gone! I couldn't believe it, but, YES, no glue! Then I washed and dried the jar real good and there was no glue residue anywhere. Next, to cut off the top of the jar, I wrapped masking tape around the area of the jar where it slanted in.

Then used a utility knife to cut through the thick plastic and around the jar following the edge of the masking tape.

Once the top was remove, the cutting edge on the bottom was a bit jagged and sharp.

Ordinarily, I would use a hot iron to make the edge round and smooth, but the jar was much larger than my iron. So I heated a small non-stick fry pan on my stove and pressed the edges of the jar firmly down and evenly against the pan until the edges began to round - which only took seconds.

I did get carried away with the edges rounding - I didn't know when to stop pressing down, lol, so I quickly remove the jar from the fry pan. Then I placed the jar over the bottom of an inverted, 2-cup glass measuring cup. Doing this helps the jar to form a perfect round shape around the opening as the plastic cools.

To make the top for the bunny jar, invert the jar and draw a circle pattern with an 1/2" overlap on thin particle board or cardboard and cut out. Then paint the circle white since its' dark color would show through the white burlap fabric.

Be sure to paint both sides of the circle and let dry.

Once the paint is dry, cover one side of the circle with Fabri-Tac glue and press the burlap fabric over the glue, smoothing out the fabric on the circle.

Then add glue to the other side of the circle and fold over the fabric to the side with the glue, smoothing out the fabric on top. Once the fabric and glue is dry, cut out the circle to make the top.

Then add Fabri-Tac around the edge of the circle in increments . . .

and begin applying the cording on top of the glue.

Adding more glue and cording until . . .

To make the bunny ears, spread glue on a small section of burlap, folding over the fabric to double it and make it thicker. Then place the bunny ear template (hand drawn) on top to . . .

cut out.

Once the ears are cut out, begin adding glue to the sides of the ears and . . .

then pressing on the cording to the glue.

One ear and then the . . .

other ear, cutting off excess cording.

Then squeeze the bottom of each ear, clamping in place until dry.

To add the bunny ears to the top, place the top on jar and . . .

add a bit of glue along the bottom cording in between the ears, pressing together at an angle. Then glue on the bunny ears at the center of the top.

Add a colorful, decorative bow to complete the look!

Enjoy the many possibilities to use this adorable Bunny Treat Jar!

I hope you enjoyed how I created a Bunny Treat Jar from a mayonnaise jar! Up next is Donna from Modern on Monticello, sharing her fabulous fabric wrapped canvas art!

Be sure to visit all of the creative projects from our Creative Craft Hop listed below!